ho attaccato alla mia slackuerina 9 appena uscita un modemusb isdn e il dmesg mi ritorna questo : Linux version 2.4.20 (root@midas) (gcc version 3.2.2) #2 Mon Mar 17 .......
......usb-ohci.c: USB OHCI at membase 0xc688e000, IRQ 11 usb-ohci.c: usb-00:01.3, Silicon Integrated Systems [SiS] 7001 (#2) usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected PCI: Found IRQ 11 for device 00:01.2 PCI: Sharing IRQ 11 with 00:01.3 usb-ohci.c: USB OHCI at membase 0xc6890000, IRQ 11 usb-ohci.c: usb-00:01.2, Silicon Integrated Systems [SiS] 7001 usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 3 ports detected sis900.c: v1.08.06 9/24/2002 PCI: Found IRQ 9 for device 00:01.1 eth0: SiS 900 Internal MII PHY transceiver found at address 1. eth0: Using transceiver found at address 1 as default hub.c: new USB device 00:01.2-1, assigned address 2 usb.c: USB device 2 (vend/prod 0x483/0x481d) is not claimed by any active driver. eth0: SiS 900 PCI Fast Ethernet at 0xd000, IRQ 9, 00:a0:cc:c0:99:b7. usb-uhci.c: $Revision: 1.275 $ time 15:38:38 Mar 11 2003 usb-uhci.c: High bandwidth mode enabled usb-uhci.c: v1.275:USB Universal Host Controller Interface driver uhci.c: USB Universal Host Controller Interface driver v1.1 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found CSLIP: code copyright 1989 Regents of the University of California ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1 loaded HiSax: Linux Driver for passive ISDN cards HiSax: Version 3.5 (module) HiSax: Layer1 Revision 1.1.4.1 HiSax: Layer2 Revision 1.1.4.1 HiSax: TeiMgr Revision 1.1.4.1 HiSax: Layer3 Revision 1.1.4.1 HiSax: LinkLayer Revision 1.1.4.1 HiSax: Approval certification valid HiSax: Approved with ELSA Microlink PCI cards HiSax: Approved with Eicon Technology Diva 2.01 PCI cards HiSax: Approved with Sedlbauer Speedfax + cards HiSax: Approved with HFC-S PCI A based cards hiax_st5481: ST5481 USB ISDN driver v0.1.0 usb.c: registered new driver st5481_usb st541: found adapter VendorId 0483, ProductId 481d, LEDs 2 HiSax: Card 1 Protocol EDSS1 Id=st5481_usb0 (0) HiSax: DSS1 Rev. 1.1.4.1 HiSax: 2 channels added HiSax: MAX_WAITING_CALLS added eth0: Media Link On 100mbps half-duplex parport0: PC-style at 0x378 [PCSPP,TRISTATE] lp0: using parport0 (polling).
Sembra che venga riconosciuto il modem, ma io che non ho mai usato ne usb ne isdn sotto linuzzo ,ora come faccio a provare a fare una chiamata ? Credo che mi servino le isdn4k-linux ma dopo averle installate come le uso ? Presumo che non posso usare minicom ....AIUTO :-))) Ciao Guido